Your Single Source Stud Welding Specialists
  • Hanger-Adhesive IHA

    Product Data:

    MIDWEST Fasteners HANGER ADHESIVE is a high strength, heavy-bodied adhesive, specifically formulated for adhering anchors for hanging insulation.

    IHA-177 HANGER ADHESIVE bonds metal and nylon anchors to metal, concrete or masonry surfaces. The product can also be used to install metal or ceramic wall fixtures and in tile applications.

    MIDWEST Fasteners HANGER ADHESIVE is also available for use as a general-purpose construction adhesive in applications requiring a high strength bond, or in applications subjected to high temperatures.

    Special Characteristics:

    • Excellent thermal shock resistance
    • High bond strength
    • Water resistant
    • Immediate grab
    • Mildew resistant
    • Non-slip formula
    Directions for Use:

    1. Use only after careful consideration of the warnings, directions, and first aid instructions given.

    2. Surface Preparation: Surfaces to be bonded should be clean, dry and free of any dust, frost, wax, moisture, dirt, grease, oil, rust, or other contaminants. Do not use over painted surfaces. Many protective coatings are not compatible with Anchor Adhesive.

    3. Adhesive Preparation: Adhesive should be stored at room temperature (60ºF to 80ºF) for at least 24 hours prior to use.

    4. Working Temperature: For best results, adhesive and materials to be bonded should be 30ºF to 120ºF.

    5. Adhesive Application: Do not apply at temperatures below 30ºF. Prepare and install one anchor at a time. Apply a dab (the size of a small walnut) of adhesive to the anchor base with a putty knife and immediately (maximum open time is 10 minutes) press anchor firmly into place, with a slight twisting motion. For proper adhesion, insure that the film of adhesive covering the anchor base (after the anchor has been firmly pressed into place) is protruding

    6. Installing Anchor Adhesive to Concrete Surfaces: New concrete surfaces need to cure a minimum of 28 days in order to ensure best adhesion. All concrete surfaces should be high pressure water blasted or sand blasted to remove any surface curing agents and all foreign matter. Spread anchor adhesive on anchor base allowing solvent to flash off for several minutes before pressing anchor firmly into place with a slight twisting motion. Do not apply load until application is completely dry.

    PACKAGING INFORMATION

    Size Packed Part # Weight
    GALLON 4/carton IHA-177-GA 39 lbs. /carton

    *MIDWEST Fasteners does not ship IHA-177 Adhesive by Air; standard shipments are UPS or Motor Freight.
    Also sold by MIDWEST only in carton-lot quantities.

    Please click the Request Information button to configure your IHA-177 Insulation Hanger Adhesive.

  • ZVOC Insulation Hanger Adhesive

    Product Data:

    Midwest IHA Zero VOC Hanger Insulation Hanger Adhesive is a cream-paste construction type adhesive. Tan in color, it is specially formulated for bonding insulation hangers to metal and unfinished masonry surfaces. IHA ZVOC dries to a tough, yet resilient bond that can withstand thermal cycling and shock.

    IHA ZVOC has been specially formulated to meet strict VOC requirements and, based on independent testing, has been MAS Certified “Green” and is LEED v4 compliant . IHA ZVOC is also designated under the following standards: Collaborative for High Performance Schools (CHPS) and California Dept. of Public Health (CDPH) Standard Method V1.1.

    Characteristics:

    • Thermal shock resistance
    • High bond strength
    • Water resistance
    • Mildew resistance
    • Immediate grab
    Directions for Use:
    1. Use only after careful consideration of the warnings, directions, and first aid instructions pertinent to this product.
    2. Be assured that surfaces to be bonded are clean and dry.
    3. Do not thin.
    4. Apply approx. 1/16th inch (1.6MM) coating of ZVOC Insulation Hanger Adhesive to the base of the hanger with a spatula or putty knife.
    5. Immediately press the hanger in place with a twisting motion.
    6. Make sure good contact is made.
    7. Always prepare and bond only one (1) hanger at a time.
    8. Allow a minimum of 48 hours drying time before installing insulation with the hange
    CLEAN UP: Xylol, or mineral Spirits
    DOT Shipping Name: UN1993, Flamable Liquid, 3, PG III

    PACKAGING INFORMATION

    Size Packed Part # Weight
    GALLON 4/carton IHA- ZVOC-GA 37.6 lbs. /carton

    *MIDWEST Fasteners does not ship ZVOC Adhesive by Air; standard shipments are UPS or Motor Freight.
    Also sold by MIDWEST only in carton-lot quantities.

    Please click the Request Information button to configure your ZVOC Insulation Hanger Adhesive.

© 2017, Midwest Fasteners.Site created by Thomas Web Solutions and powered by Navigator Platform